Compare products

5” DA Pad – 5/16-24
for the IT-7311W5, IT-7445 and IT-7785. PSA – Has vinyl face for pressure sensitive adhesive abrasives.

Quality drills for production use. The IT-7768R has a convenient forward and reverse lever, rear exhaust and all ball bearing construction. Comes standard with a quality drill chuck with a range of 0 to 3/8” and superior holding power. Variable speed and three gear system make this our best 3/8” drill. IT-7768 is the same great tool in forward only.

Tool comes standard with one head, either 6-32, 8-32, 10-24, 10-32, 1/4-20, 5/16-18, M3, M4, M5, M6 or M8. Additional heads available separately.

Our One Shot hammers are designed for operations requiring less power, including driving oil seals, bushings and pins. Every pull of the lever delivers a single blow that can be regulated by adjusting the air pressure.

Plenty of power for the toughest jobs. Will drive pins, cut sheet metal, scrape or cut steel, aluminum, wood, stone or concrete. The IT-7151 has a longer stroke and heavier piston. The IT-7111 has a shorter stroke and piston and higher BPM making it more suitable for panel cutting.

The 1/4-28 Drill Motors shown here give a wide range of use for tight spots encountered in aircraft manufacturing and any type of production drilling situation.

When plenty of reliable power is needed, the IT-7801 will provide it. Cuts sheet metal, fiberglass, muffler clamps and hangers. Grinds burrs and rough edges.

The IT-8957R is a remarkable tool. The direction of rotation can be changed to throw grinding sparks the opposite direction. This allows the operator to avoid contaminating nearby materials.

The IT-7768HR and IT-7768HRK have convenient forward and reverse lever, rear exhaust and all ball bearing construction.

A great tool for heavy duty scaling, the IT-7601 has a well cushioned rubber handle, heat treated piston and barrel.

5” DA Pad – 5/16-24 for the IT-7311W5, IT-7445 and IT-7785. Has velcro face for abrasives with the hook and loop system.

This unique shredder has many uses. The roller on the back of the tool acts as a pivot point so that more or less pressure can be applied. Carbide wheel cuts fiberglass, concrete, wood, plastic and many other materials.

Ratchet wrenches are exceptionally good at doing the job they are designed for – removing fasteners after they have first been loosened. It is important to keep the ratchet mechanism clean and free of sand and grit. Sand will wear out the ratchet mechanism and cause premature tool failure. Use an air blow gun to clean the head after extended use.

The T-7121 is a Super Duty Air Hammer that produces up to 3000 blows per minute at 90 PSI. Excellent for cutting, crimping, driving pins, bushings, shearing and for front end work. Long life cylinder with hardened and ground piston. Metal valve blocks.

5″ Velcro Pad for IT-7815A and tools under 15,000 RPM.

Compact to work in confined spaces. The IT-7757D cannot be damaged by overloading. Drill, brush, hone or deburr without hazard of electric shock. (Not for use with cast wheels or accessories not rated for 25,000 RPM.)

The IT-9555 & IT-9556 sanders are our smoothest running DA Sanders. Metal rotors and fiberglass pads help to improve cutting action and durability.

Compact, lightweight and hard hitting. The IT-8839 and IT-8839A have composite housings that are ideal for your toughest job. Twin hammer clutches have lots of power. Tool exausts through the bottom of the handle. Built-in regulator.

A great 1/2” production drill with HiTorque Double reduction gears.

5” DA Pad for use with IT-7555VAC Spindle size 5/16-24 PSA vinyl face.

Designed to be used in tight areas where only an angle can reach. Compact and easy to use, the angle head can be rotated 360 degrees.