Compare products

*Teasing Throttle
*1/2 HP motor provides power through hardened planetary gear system
*Cutting head adjustable 360 degrees in 90 degree increments

The IT-7768HR and IT-7768HRK have convenient forward and reverse lever, rear exhaust and all ball bearing construction.

The IT-7815A features heavy duty alloy steel gears, safety lock off lever, lightweight aluminum housing, built-in regulator and convenient side handle. Rear exhaust.

The IT-7761 & IT-7761AH are reversible and produce accurate torque. The clutches are internally adjustable and feature rear exhaust.

5″ Velcro Pad for IT-7815A and tools under 15,000 RPM.

Spare pads for the IT-7211 & IT-7511.

•Heavy Duty 5/8” Drill
•Plenty of Power
•Side Handle
•Tapered Chuck
•Twin Hammer Clutch

* Built-in regulator
* Ball bearing construction
* Lightweight aluminum housing
* Exhausts through handle
* Rugged 1 HP motor

The IT-7315 removes material from large areas with ease. The synchronized dual pistons give a smooth action that reduces operator fatigue.

Manual torque adjustment – tighten or loosen internal spring

*Regulator
*Full ball bearing construction *Built-in silencer
* 1/8” Orbit

Our best 2” DA Sander for getting in hard to reach spots where finish work is needed.

Tapping Capacity-Aluminum: M3-M12
Tapping Capacity-Steel: M3-M8
Free Speed: 150 RPM
Length: 7.87″
Weight: 4.10 lbs.
Air Pressure: 90 PSI Max.

The T-7121 is a Super Duty Air Hammer that produces up to 3000 blows per minute at 90 PSI. Excellent for cutting, crimping, driving pins, bushings, shearing and for front end work. Long life cylinder with hardened and ground piston. Metal valve blocks.

The T-7121 is a Super Duty Air Hammer that produces up to 3000 blows per minute at 90 PSI. Excellent for cutting, crimping, driving pins, bushings, shearing and for front end work. Long life cylinder with hardened and ground piston. Metal valve blocks.

The IT-7445/IT-7446 have a smaller grip to better fit smaller hands. They both come with regulators and muffled exhaust.

A great tool for heavy duty scaling, the IT-7601 has a well cushioned rubber handle, heat treated piston and barrel.

Make distortion free cuts with the IT-7700N and IT-7701. The blades shear the material giving a clean cut. A 1/4” strip of material is removed by the cutting action or can be used to trim one edge. Loosen one screw to rotate head 360 degrees.

Tool comes standard with one head, either 6-32, 8-32, 10-24, 10-32, 1/4-20, 5/16-18, M3, M4, M5, M6 or M8. Additional heads available separately.

Sander Backup Pads for IT-7778.

The IT-7553 is small, compact and easy to use. It features heavy-duty ball bearing construction, built-in regulator and a smooth powerful cutting action. The 3” velcro pad makes for easy attachment of sanding disks. The 3/32” Orbit gives a fine finish for the most demanding work.

A must for every glass shop. Cuts incapsulated glass with ease. Also works great for cutting material out of expansion joints. Sharp blades and cutting action of this tool make for an excellent caulking and putty scraper – even cuts wood. Double head bearings for trouble free service.

Small and easy to use, the IT-7702 cuts straight and curved shapes. Cuts aluminum, mild steel, plastic and fiberglass with ease. Comes with two blades (24 & 32 TPI).

IT-6416VV Velcro Vacuum Pad

The IT-7665 is small, compact and easy to use. It features heavy-duty ball bearing construction, built-in regulator and a smooth powerful cutting action. The vinyl face pad makes for easy attachment of PSA sandpaper. Pad size is 90 x 90 x 80mm. Triangular Pad allows use in corners and tight spots. The 1/8” Orbit gives a fine finish and heavy cutting action for the most demanding work. Can be used for sanding, polishing and scrubbing.

The IT-7555B/IT-7556B have the same great specs as the IT-7555/IT-7556, but have a 3/32” orbit that can give a finer finish.

Built for production, the IT-7705 comes complete with round, flat, triangular and bastard files.
Order extra file set part IT-770501 (4 pcs.)