Compare products

When plenty of reliable power is needed, the IT-7801 will provide it. Cuts sheet metal, fiberglass, muffler clamps and hangers. Grinds burrs and rough edges.

3-1/2” Polishing Pad for the IT-7553. For use with 755338V velcro pad.

7″ PSA Pad

Compact, lightweight and hard hitting. The IT-8839 and IT-8839A have composite housings that are ideal for your toughest job. Twin hammer clutches have lots of power. Tool exausts through the bottom of the handle. Built-in regulator.

The IT-8758R and IT-8759R are the .35 HP version of the IT-8859R. With plenty of power and their smaller size, these tools are a must for production grinding. As with all die grinders, use of balanced stones and accessories are required. Also using a maximum of 90 PSI at the tool and oiling daily at the end of each shift will give extended life to the tool.

The IT-9870 & IT-9890 give added versatility with their 1/4” collets and threaded collets for 1/4-28 on the IT-9870 and 5/16-24 on the IT-9890. Quality one piece angle heads and unique lock off levers make these tools long lasting and comfortable to use.

Quality drills for production use. The IT-7768R has a convenient forward and reverse lever, rear exhaust and all ball bearing construction. Comes standard with a quality drill chuck with a range of 0 to 3/8” and superior holding power. Variable speed and three gear system make this our best 3/8” drill. IT-7768 is the same great tool in forward only.

Straight Handle Rivet Gun, .401 Shank Rivet Gun.

Both tools are lightweight, powerful production routers. Easily adjustable. Direct drive motors have no gears to wear. Complete with lock off levers and rear exhaust. All aluminum router base.

Sander Backup Pads for IT-7778.

Replacement 5″ pad for IT-7815A

The IT-7556VAC/IT-7555VAC have the same great specs as the IT-7556/IT-7555, but are set up to be attached to an industrial vacuum cleaner.

This unique shredder has many uses. The roller on the back of the tool acts as a pivot point so that more or less pressure can be applied. Carbide wheel cuts fiberglass, concrete, wood, plastic and many other materials.

Tapping Capacity-Aluminum: M3-M12
Tapping Capacity-Steel: M3-M8
Free Speed: 150 RPM
Length: 7.87″
Weight: 4.10 lbs.
Air Pressure: 90 PSI Max.

The IT-7445/IT-7446 have a smaller grip to better fit smaller hands. They both come with regulators and muffled exhaust.

5″ Velcro Poly Pad 5/8-11 for IT-8818P

The IT-7749 has a steel clutch cover for use in demanding applications. A strong tool with 500 ft.lbs torque in forward and 600 ft.lbs. in reverse.

Ratchet wrenches are exceptionally good at doing the job they are designed for – removing fasteners after they have first been loosened. It is important to keep the ratchet mechanism clean and free of sand and grit. Sand will wear out the ratchet mechanism and cause premature tool failure. Use an air blow gun to clean the head after extended use.

A must for every glass shop. Our IT-7838B is a quality tool at an affordable price.

Straight Handle Rivet Gun, .401 Shank Rivet Gun.

5” DA Pad – 5/16-24
for the IT-7311W5, IT-7445 and IT-7785. PSA – Has vinyl face for pressure sensitive adhesive abrasives.

The IT-3010 holds 14 ounces (approximately 400cc) of grease. May be loaded from a tube, from a bulk dispenser, by suction, or by filling it with a scoop.

5” DA Pad – 5/16-24 for the IT-7311W5, IT-7445 and IT-7785. Has velcro face for abrasives with the hook and loop system.

The IT-7888 is a small precision 1/4” drill with plenty of power. Fits in the palm of your hand. Choose from four chuck options.

The IT-5540 precision 3/8” non reversing drill features smooth two speed throttle, strong .7 HP motor, side handle for right or left hand use, quiet rear exhaust and roller bearings in the gears. Choose from three drill chuck options.

The beauty of the IT-9825NK is two fold. A 1/4” & a 3/8” drive are in IT-9825NK the kit. Just remove drive and flip it around for reverse. The second part is that a set of 10 sockets are with the tool, that fit directly into the head, leaving the center open so that a threaded rod or long bolt can pass through.

The IT-9555 & IT-9556 sanders are our smoothest running DA Sanders. Metal rotors and fiberglass pads help to improve cutting action and durability.

The IT-9888R is a quality 1/4” drill with the same teasing throttle control as above and a convenient reversing lever. Multi directional exhaust cover channels exhaust away from user. Quiet and comfortable, the cushioned grip and quiet operation makes this the perfect 1/4” Palm Drill. Shown with precision 1/4” chuck. Also available with 1/4”Composite Keyless chuck as IT-9888RK and with 1/4” Hi-Precision Geared chuck as IT-9888RSPC.

IT-7788HR-KCN 1/2” Keyless Drill Chuck. Makes changing drill bits easy. This chuck can be used for for- ward and reversible drills. 3/8-24 threads. 1/2” capacity.

The IT-7888 is a small precision 1/4” drill with plenty of power. Fits in the palm of your hand. Choose from four chuck options.

Non-reversible, The IT-9888 is a quality 1/4” drill with the teasing throttle control you need. Multi directional exhaust cover channels exhaust away from user. Quiet and comfortable, the cushioned grip and quiet operation makes this the perfect 1/4” Palm Drill. Shown with precision 1/4” chuck. Also available with 1/4” Composite Keyless chuck as IT-9888K, with 1/4” Metal Keyless chuck as IT-9888MK and with 1/4” Hi-Precision Geared chuck as IT-9888SPC.