Compare products

5” DA Pad – 5/16-24
for the IT-7311W5, IT-7445 and IT-7785. PSA – Has vinyl face for pressure sensitive adhesive abrasives.

Quality drills for production use. The IT-7768R has a convenient forward and reverse lever, rear exhaust and all ball bearing construction. Comes standard with a quality drill chuck with a range of 0 to 3/8” and superior holding power. Variable speed and three gear system make this our best 3/8” drill. IT-7768 is the same great tool in forward only.

Tool comes standard with one head, either 6-32, 8-32, 10-24, 10-32, 1/4-20, 5/16-18, M3, M4, M5, M6 or M8. Additional heads available separately.

Our One Shot hammers are designed for operations requiring less power, including driving oil seals, bushings and pins. Every pull of the lever delivers a single blow that can be regulated by adjusting the air pressure.

Plenty of power for the toughest jobs. Will drive pins, cut sheet metal, scrape or cut steel, aluminum, wood, stone or concrete. The IT-7151 has a longer stroke and heavier piston. The IT-7111 has a shorter stroke and piston and higher BPM making it more suitable for panel cutting.

The 1/4-28 Drill Motors shown here give a wide range of use for tight spots encountered in aircraft manufacturing and any type of production drilling situation.

When plenty of reliable power is needed, the IT-7801 will provide it. Cuts sheet metal, fiberglass, muffler clamps and hangers. Grinds burrs and rough edges.

The IT-8957R is a remarkable tool. The direction of rotation can be changed to throw grinding sparks the opposite direction. This allows the operator to avoid contaminating nearby materials.

The IT-7768HR and IT-7768HRK have convenient forward and reverse lever, rear exhaust and all ball bearing construction.

A great tool for heavy duty scaling, the IT-7601 has a well cushioned rubber handle, heat treated piston and barrel.

5” DA Pad – 5/16-24 for the IT-7311W5, IT-7445 and IT-7785. Has velcro face for abrasives with the hook and loop system.

This unique shredder has many uses. The roller on the back of the tool acts as a pivot point so that more or less pressure can be applied. Carbide wheel cuts fiberglass, concrete, wood, plastic and many other materials.

Ratchet wrenches are exceptionally good at doing the job they are designed for – removing fasteners after they have first been loosened. It is important to keep the ratchet mechanism clean and free of sand and grit. Sand will wear out the ratchet mechanism and cause premature tool failure. Use an air blow gun to clean the head after extended use.

The T-7121 is a Super Duty Air Hammer that produces up to 3000 blows per minute at 90 PSI. Excellent for cutting, crimping, driving pins, bushings, shearing and for front end work. Long life cylinder with hardened and ground piston. Metal valve blocks.

5″ Velcro Pad for IT-7815A and tools under 15,000 RPM.

Compact to work in confined spaces. The IT-7757D cannot be damaged by overloading. Drill, brush, hone or deburr without hazard of electric shock. (Not for use with cast wheels or accessories not rated for 25,000 RPM.)

The IT-9555 & IT-9556 sanders are our smoothest running DA Sanders. Metal rotors and fiberglass pads help to improve cutting action and durability.

Compact, lightweight and hard hitting. The IT-8839 and IT-8839A have composite housings that are ideal for your toughest job. Twin hammer clutches have lots of power. Tool exausts through the bottom of the handle. Built-in regulator.

A great 1/2” production drill with HiTorque Double reduction gears.

5” DA Pad for use with IT-7555VAC Spindle size 5/16-24 PSA vinyl face.

Designed to be used in tight areas where only an angle can reach. Compact and easy to use, the angle head can be rotated 360 degrees.

The perfect tools for cleaning and polishing dies, porting and polishing engines, de-burring castings and any job where carbide burrs or stones are used for delicate material removal. The IT-7401 now comes in a storage case with oil bottle, quick disconnect fitting, IT-5830 oiler and 2 collet wrenches.

The T-7121 is a Super Duty Air Hammer that produces up to 3000 blows per minute at 90 PSI. Excellent for cutting, crimping, driving pins, bushings, shearing and for front end work. Long life cylinder with hardened and ground piston. Metal valve blocks.

The IT-7556VAC/IT-7555VAC have the same great specs as the IT-7556/IT-7555, but are set up to be attached to an industrial vacuum cleaner.

The IT-9707 & IT-9709 are super duty grinders designed for production grinding in foundries, shipyards, fabrication shops and any application that requires a powerful, lightweight grinder.

IT-7788-A 3/8” Standard Jacobs Multicraft Drill Chuck. 3/8-24 threads. Key is model IT-7788-B. Chuck and key are model IT-7788-C. This chuck can be used on forward and reversible drills. Capacity 3/8″

•Quality hardened gears
•Rear Exhaust
•Variable Speed
•Forward and Reverse
•Angle head reaches into tight areas

•Quality hardened gears
•Rear Exhaust
•Variable Speed
•Lightweight aluminum handle

*Teasing throttle
*Ball type socket retainer *Triple idler gear system *Light, easy to grip aluminum handle
*3/4 HP motor

This high torque ratchet handles those tough fasteners in tight places.

Straight Handle Rivet Gun, .401 Shank Rivet Gun.

The IT-9915 series of grinders are built for production and long life. Adjustable exhaust, Heavy duty safety lockoff lever. Use type 27 wheels (not included).

The IT-9940EXD is an exceptionally Heavy Duty 3/8” Angle Drill. Free Speed is 13,500, Spindle size is 3/8-24, Weight is 4 lbs., length is 12.5”. Forward direction only. Air cons. @ load- 26CFM

The IT-7838D comes complete with air supply hose and exhaust hose. Also provided is our IT-783851 2-1/2” offset blade. This tool is a must for every glass shop and may be used with a wide range of blades.

The IT-7445/IT-7446 have a smaller grip to better fit smaller hands. They both come with regulators and muffled exhaust.

*Operates in any position
*Tool stops when nail is set
*Drives up to 60 penny nails
*Pressure activated

A great 1/2” production drill with HiTorque Double reduction gears.

The IT-7888A is a small precision 1/4” drill with plenty of power that fits in the palm of your hand. Rubber grip reduces vibration and improves grip.