Compare products

Spare pads for the IT-7211 & IT-7511.

The IT-7445/IT-7446 have a smaller grip to better fit smaller hands. They both come with regulators and muffled exhaust.

IT-6120 Quick Change Spring for .498 Shank Hammers

This unique sander has many uses. The roller on the right of the tool acts as a pivot point so that more or less pressure can be exerted. Side guide can be used for straight passes. Boss on right of tool for vacuum hookup. Includes on 60 grit belt.

IT-7788-A 3/8” Standard Jacobs Multicraft Drill Chuck. 3/8-24 threads. Key is model IT-7788-B. Chuck and key are model IT-7788-C. This chuck can be used on forward and reversible drills. Capacity 3/8″

Straight Handle Rivet Gun, .401 Shank Rivet Gun.

The IT-7315 removes material from large areas with ease. The synchronized dual pistons give a smooth action that reduces operator fatigue.

*Teasing Throttle
*1/2 HP motor provides power through hardened planetary gear system
*Cutting head adjustable 360 degrees in 90 degree increments

The IT-7445/IT-7446 have a smaller grip to better fit smaller hands. They both come with regulators and muffled exhaust.

The IT-7665 is small, compact and easy to use. It features heavy-duty ball bearing construction, built-in regulator and a smooth powerful cutting action. The vinyl face pad makes for easy attachment of PSA sandpaper. Pad size is 90 x 90 x 80mm. Triangular Pad allows use in corners and tight spots. The 1/8” Orbit gives a fine finish and heavy cutting action for the most demanding work. Can be used for sanding, polishing and scrubbing.

*Built-in Regulator
*1/2 HP motor
*Full ball bearing construction
*Built-in silencer
*Balanced counter weight design
*Locking shaft for easy pad removal
*Available with Velcro pad (specify when ordering)
*3/8” Orbit

The IT-9988HD is small, compact, lightweight and strong. This tool easily drills 1/2” holes in concrete. Comes with cushioned grip, side handle and 1/2” drill chuck.

The perfect tool for removal of dried out gasket material.
The IT-7703 will not harm underlying surface when using at the correct angle.

*Lightweight
*Marks on materials up to 64R in hardness
*Trouble free piston design
*Low air consumption
*Twist throttle

*1/2” Jacobs Chuck
*Requires only 5-1/2” Clearance
*One to one gear ratio
*Not for use with bits larger than 1/2”

*Includes 3” Foam back Velcro pad.
*Rear Exhaust
*For use on steel, aluminum, wood, plastic, rubber etc. *Rubber comfort grip *Ideal for sanding and polishing

*Teasing throttle
*Exhausts through bottom of handle
*Convenient forward and reverse lever
*Built to last

IT-7888-SPA 1/4” Special Jacobs 1BA Drill Chuck. 3/8-24 threads. Key is model IT-7888-SPB. Chuck and key are model IT-7888- SPC. This chuck can be used on forward and reversible drills. Capacity 0 to 1/4”.

Tapping Capacity-Aluminum: M3-M12
Tapping Capacity-Steel: M3-M8
Free Speed: 150 RPM
Length: 7.87″
Weight: 4.10 lbs.
Air Pressure: 90 PSI Max.

A must for every glass shop. Cuts incapsulated glass with ease. Also works great for cutting material out of expansion joints. Sharp blades and cutting action of this tool make for an excellent caulking and putty scraper – even cuts wood. Double head bearings for trouble free service.

(uses our IT-9801341 4” Cutoff Wheel) same great tool as the IT-8801REX, but with short reach

The IT-5540 precision 3/8” non reversing drill features smooth two speed throttle, strong .7 HP motor, side handle for right or left hand use, quiet rear exhaust and roller bearings in the gears. Choose from three drill chuck options.

Ratchet wrenches are exceptionally good at doing the job they are designed for – removing fasteners after they have first been loosened. It is important to keep the ratchet mechanism clean and free of sand and grit. Sand will wear out the ratchet mechanism and cause premature tool failure.

3-1/2” Polishing Pad for the IT-7553. For use with 755338V velcro pad.

This unique shredder has many uses. The roller on the back of the tool acts as a pivot point so that more or less pressure can be applied. Carbide wheel cuts fiberglass, concrete, wood, plastic and many other materials.

The IT-7888 is a small precision 1/4” drill with plenty of power. Fits in the palm of your hand. Choose from four chuck options.

The 1/4-28 Drill Motors shown here give a wide range of use for tight spots encountered in aircraft manufacturing and any type of production drilling situation.